Quads
Machine

Leg Press

How to do the leg press, what it works, the kit you need and the cues that keep the reps honest.

Leg Press demonstration

Muscles worked

Primary: Quads. Also works: Glutes, Hamstrings, Calves.

Equipment

machine · Strength.

How to do it

  1. 1

    Adjust the seat and footplate of the sled machine to a comfortable position.

  2. 2

    Sit on the sled machine with your back against the backrest and your feet shoulder-width apart on the footplate.

  3. 3

    Grip the handles on the sides of the seat for stability.

  4. 4

    Push the footplate away from your body by extending your legs, keeping your heels on the footplate.

  5. 5

    Continue pushing until your legs are almost fully extended, but without locking your knees.

  6. 6

    Pause for a moment at the top of the movement, then slowly lower the footplate back towards your body by bending your knees.

  7. 7

    Repeat for the desired number of repetitions.

Coaching cues

  • Control the eccentric — the lowering phase drives most of the growth stimulus.
  • Keep the quads doing the work; if other muscles take over, reduce the load.
  • Match your range of motion to what you can hold without shifting position.

Leg press: technique checkpoints

The leg press trains the quads and glutes, with the hamstrings helping. Because the seat supports your back, you can work your legs hard without balancing a bar, which makes it a useful squat partner or replacement.

Sit with your lower back and backside pressed into the pad. Place your feet about shoulder-width apart on the platform, then lower it under control until your knees are well bent, stopping just before your lower back or hips start to lift off the pad.

Push through your whole foot with your heels down, and keep your knees moving in line with your toes. Finish with your legs almost straight rather than locking your knees hard at the top.

Common mistakes and what to change

  • Lower back or hips lifting off the pad: stop each rep just before this happens. Moving your feet a little higher on the platform often lets you go deeper with your back still flat.
  • Heels lifting off the platform: move your feet higher up the platform or reduce depth slightly so your whole foot stays flat.
  • Locking the knees hard at the top: finish with a soft bend in the knee and keep tension in your legs between reps.
  • Knees caving inwards: push your knees out in line with your toes. If they still cave, lower the weight.
  • Short, bouncing reps with a heavy stack: use a weight you can lower slowly to the same depth each time. Bigger numbers from shorter reps don't mean stronger legs.

Choosing a related movement

A single-leg press shows if one side does more work. A hack squat or barbell back squat adds more balance and core work, and a Bulgarian split squat trains each leg on its own with only dumbbells. Leg extensions add extra quad work afterwards. Leg press weights don't transfer to squats, so log each one separately.

Sets, reps and progression

Work in a rep range, for example 3 sets of 8–12, finishing each set with one or two good reps still available. Keep the same depth and foot position every session so the numbers you log are comparable.

Once every set reaches the top of the range at full depth with your back flat on the pad, add a small amount of weight next session, such as 5 kg in total. If that drops you well below the range, stay at the current weight and add reps or a slower lowering phase first.

Improve reps before adding weight. Pulse suggests your next weight and reps from what you logged last time, so you don't have to remember them.

Common questions

How deep should I go on the leg press?

Go as deep as you can while your lower back and backside stay on the pad and your heels stay down. For many people that is somewhere around or past a 90-degree bend at the knee, but it depends on your hips, ankles and the machine. Your depth will often improve with practice.

Is 90 degrees at the knee deep enough?

It is a reasonable starting point, and it is much better than very short reps. If you can go a little deeper with your back still flat and heels down, that extra range trains the quads and glutes through more of their length. If going deeper makes your lower back lift, stay at the depth you can control.

Is it bad if my lower back lifts off the pad?

Your lower back lifting or rounding at the bottom means you have gone deeper than your hips allow in that position, and the extra load moves into your back instead of your legs. Stop each rep just before it happens, or move your feet slightly higher on the platform. If you feel pain, stop the set.

Does foot position change which muscles work?

A little, but less than many charts suggest. Feet lower on the platform let your knees bend further, which tends to put more work on the quads. Feet higher shift some work towards the glutes and hamstrings. Wide or narrow stances change how it feels more than which muscles grow. Pick the position that lets you reach good depth comfortably and keep it the same so your progress is easy to track.

Keep browsing

Alternatives and related movements

Cite or link to this page

Coaches, physiotherapists and fitness writers are welcome to reference this exercise guide.

Pulse. (2026). Leg Press: How to, muscles worked and form cues. Pulse Exercise Library. https://pulsecoach.online/exercises/leg-press

Train it, log it, beat it

Add the leg press to a program that tracks your loads, suggests the next weight and adjusts to how recovered you are.

Create your free account

Training guidance only — not medical advice. See our terms.